FIRST HUMAN PILOT / MATCHED B′72 + B72 CONDITIONS
Start with the small C1 mockup.
5.2 × 3.4 m · two tables · twelve chairs · one boundary segment.
Read the one-page checklist first, then use the procedure and files below.
C1 / P1 FIELD PROTOCOL · ENGLISH · 29 OCT 2026
Set up. Make the move. Record the return.
C1 / First pilot checklist
One English A4 sheet for the 5.2 × 3.4 m local mockup: equipment, people, installation and matched B′72/B72 trial order.
Download the one-page C1 checklist
Read the C1 checklist on this page
12 local chairs; both full designs retain 72 seats. No scent. Field aid: the C1 drawings and P1 procedure govern; use the two-page record.
01 / Bring
- Two stable tables, 12 floor-supported chairs and one supported boundary, exchanged between B′72 and B72. Keep observers, spare items and support feet outside the route.
- C1 A3 drawings (4 pages, 1:20), A0 template (1:1), coordinates, P1 procedure and one two-page record per attempt, practice included. Allow 8 records per mover plus retry spares.
- Tape/laser, square, low-profile removable marks, seat labels, stopwatch and pens. Photograph or sketch the empty setup; video requires separate consent.
02 / Assign people and seats
- Base: 6 people = mover + 3 peers + facilitator (brief/cue/stop) + recorder. Chair A = T4/S6; chair B = T5/S4. Peers: T4/S1, S3, S4. T4/S2, S5 empty; all T5 seats initially empty. Reserve A/B.
- O1 adds 5 occupants at T5/S1, S2, S3, S5, S6 (11 people). T5/S4 free; T4/S2, S5 stay empty. Same people/seats in both layouts; no bags/mannequins as substitutes. B72 is a layout, not chair B.
03 / Install in this order
- Print at 100%, Fit/Shrink off. Check A3 O-X and O-Y = 50 mm each; A0 line = 100 mm and bold rail = 455 mm. Verify both directions and any tiled assembly.
- Measure real table/chair footprints, heights, chair weight/glides and floor. Use stable furniture on the floor; do not raise chairs to model Z20. Record differences under one shared proxy revision.
- Mark O at T4 centre; +X along its long axis, +Y to its left. Site O-X/O-Y = 1000 mm, X-Y = 1414.2 mm. Mark the two ±1000 mm control points before covering O (2000 mm apart).
- Place tables, then all 12 chairs from A3 page 3; label T4/S1-S6 and T5/S1-S6, matching facing angles. Match template rails only if the chair fits. Mark A/B rest and 300 mm-back references; never force that pull.
- Install the page-4 boundary: B′72 four outline points; B72 sixteen. Keep 140 mm thickness, 1100 mm height and stable supports. Tape alone changes the test.
- Survey, correct and photograph the setup. ±5 mm is only a setup/reset target. Keep furniture and all other conditions matched; exchange only the boundary outline and re-survey.
04 / Run matched blocks
- P01: B′72 first, then B72. Later odd IDs use that order; even IDs reverse it. Finish one layout block before changing the boundary. ID key: Bp = B′72; B = B72. Example: P01-Bp-E1.
PR → E1 → rest ≥2 min → E2
→ rest → [O1, if eligible]
PR = unscored practice; E1/E2 = base trials. O1 = separate occupied trial, only if base runs leave no unresolved contact, instability or discomfort and the mover wishes to continue. If skipped, write NOT RUN + reason in the O1 sheet’s outcome area; leave observations blank.
Rest after PR + E1 (at least 2 minutes), before O1 and after changing layouts. Record all rest lengths; extend on request. P1 does not specify the latter two durations. Rest/hold settings are not validated comfort limits.
05 / Brief, observe, reset
- Confirm voluntary participation/right to stop; read the P1 briefing. A stays pulled out while away; B is restored after leaving it. No coached side, grip, posture or taped route.
- Start seated at A, both chairs at rest. Say Go and time. After settling at B, hold 10 seconds; say Return. End seated back at A with both chairs restored, on declared finish, or on a stop; label the actual outcome.
- Record A pull, BOTH B pulls, route, contact, help and participant wording. Before reset, measure the largest foot/rail-point offset on each chair, including rotation. Reset A/B; check the other 10 chairs, peers, boundary and datum.
06 / Stop and decide
- STOP on request, discomfort, imbalance, shifting support or unexpected body contact, including a brush. Ordinary seat contact and intentional chair grip are expected. Help end the attempt if needed; record stage, reason, chair states and assistance.
- Keep outcomes distinct: unaided / assisted complete, reset incomplete, stopped, not run. One -R1 retry only after cause resolution, reset and agreement; retain the original. Compare E with E, O1 with matched O1. Physical changes need a new shared revision in BOTH layouts.
C1 / Q1 · 30 OCT 2026 · Companion to P1 (29 OCT). No physical results recorded. Local study extent, not certified clearance; no whole-room access, scent reduction or comfort claim.
Use this sequence for the nearby move T4/S6 → T5/S4 → T4/S6. Install the same furniture for both layouts; exchange the straight B′72 boundary for the curved B72 boundary. This is a local, formative movement observation. No physical results have been recorded.
Continue to the complete procedure ↓ · Download the matching two-page record
- Calibrate the drawings and mark the datum.
- Install and measure furniture, then the boundary.
- Assign seats and rehearse the participant briefing.
- Run one practice, two base trials and one occupied trial per layout.
- Record movement, chair states and assistance; reset after every run.
- Compare like-for-like conditions before making a shared revision.
Chair A = original T4/S6. Chair B = destination T5/S4. B72 names the curved layout, not a chair. Keep A available and pulled out while the mover is away.
01 / Installation checklist
Bring: the A3 drawings, A0 footprint template, one two-page record for every run including practice, tape measure, square, low-profile floor tape, removable seat labels, stopwatch and pen. Use two stable tables, twelve stable chairs and one supported boundary segment. Keep observers and spare materials outside the movement area.
- Check the print. Print at 100% actual size, with Fit/Shrink disabled. On A3, both O–X and O–Y must measure 50 mm on paper for 1000 mm on site. On A0, the horizontal calibration line is 100 mm and the long edge of either bold sled rail is 455 mm. Measure both directions and enter the four values on the record. If tiled, check the assembled template before using it.
- Check the physical furniture first. Measure table top, height and base; chair footprint, floor-to-seat height, backrest height, type, weight and glides. Record the floor finish. The model's rail minimum is Z20, not a resolved physical support detail. Do not elevate real furniture to reproduce it or fabricate furniture from these drawings. Use stable floor-supported furniture and record differences as a physical-proxy revision.
- Mark the station and datum. Use the 5.2 × 3.4 m dashed area on A3; this is the local study extent, not a certified clearance. Mark O at the T4 centre, +X along its long axis and +Y to the left of +X. Check O–X = 1000, O–Y = 1000 and X–Y = 1414.2 mm. Add labelled control points (−1000, 0) and (+1000, 0) before T4 covers O; their separation is 2000 mm.
- Place tables, then all twelve chairs. Use A3 page 3 for centres and facing angles. Rotate the A0 template to each chair's facing; match the two rails only if the real chair has that footprint. Label T4/S1–S6 and T5/S1–S6. Do not rearrange non-moving seats to make the trial easier.
- Mark A and B in two states. Mark the rest position and the position 300 mm backwards along each chair's own facing axis. These are reference positions from the digital cycle. Record actual pull distances; do not force a person to achieve a mark. The other ten chairs remain on their rest marks.
- Install the boundary. Use A3 page 4: B′72 has four outline vertices; B72 has sixteen. Connect the points in order and close the outline. Retain the specified 140 mm thickness and 1100 mm overall height. Use a stable physical boundary; floor tape alone is a different test. Keep support feet outside the movement route and document them. Do not substitute one straight chord for the curved outline.
- Survey and release the setup. Measure maximum centre/outline deviation, facing angles, boundary height/thickness and all furniture differences. Aim for ±5 mm when setting out; this is a survey target, not a movement allowance. Correct out-of-target positions before starting. Unavoidable furniture or support differences must be recorded under one shared proxy revision in both layouts. An unmatched setup is not a matched comparison.
- Photograph or sketch the empty setup and seat labels. Record the revision and layout before people enter. Keep the same furniture, floor, lighting, table contents and boundary material/finish in the other layout. Change only the boundary plan geometry. Record unavoidable differences instead of concealing them.
02 / Roles, occupied seats and matched trial order
Roles: one mover, three original peers, one facilitator and one observer/recorder. The occupied condition adds five destination occupants. The facilitator briefs, gives start/return cues and can stop the run; the observer records. Peers stay in a normal working posture and keep their chairs fixed. Any spontaneous help or chair movement is recorded.
- Base condition (E)
- Mover starts at T4/S6. Peers occupy T4/S1, S3 and S4. T4/S2 and S5 are empty. All six T5 seats start empty. T5/S4 is reserved for the mover; T4/S6 remains reserved throughout.
- Occupied condition (O)
- Keep the same three T4 peers. Add occupants at T5/S1, S2, S3, S5 and S6. T5/S4 remains available for the mover. Do not substitute bags or mannequins for occupants within a matched pair.
- Match across B′72 and B72
- Same mover, peers and extra occupants in the same seats; same clothing/footwear, furniture identities, floor, contents, lighting, briefing, 10-second destination hold and rest rule. No scent is added. Record changes or missing occupants and do not pool those runs with the matched condition.
Layout order: odd participant IDs (P01, P03…) run B′72 then B72; even IDs run B72 then B′72. Complete one layout block before exchanging the boundary. Recheck the installation after the exchange. For one participant, order effects remain unresolved; do not describe a layout difference as a proven curvature effect.
| Run suffix | Condition | Use |
|---|---|---|
| PR | Base E | One unscored familiarisation cycle. Record it as practice. |
| E1 | Base E | First recorded cycle. |
| E2 | Base E | Second recorded cycle, after reset. |
| O1 | Occupied O | One separate feasibility observation with all five extra occupants. |
Use IDs such as P01-Bp-E1 and P01-B-O1; Bp means B′72. After PR + E1, provide at least two minutes' rest, and provide another rest before O1 and after changing layouts. Extend a rest whenever requested and record its length. Proceed to O1 only after the base runs finish without unresolved discomfort, instability or unexpected contact and the participant wishes to continue. Otherwise mark O1 not run, with the reason. Do not compare unmatched conditions.
These repeat counts, the 10-second hold and two-minute rest are practical protocol settings, not validated comfort thresholds. Base always precedes occupied, so do not infer a causal occupancy effect. This is a formative pilot, not a statistical demonstration of superiority.
03 / Participant briefing and the complete chair sequence
Confirm voluntary participation and the right to stop before starting. Video requires separate consent. Explain the task verbally; do not show the digital choreography or coach a preferred side, hand, step length or body angle before the natural trials.
“Go to the marked seat at the next table, sit and settle, then return to your own seat when I say ‘return’. Leave your own chair pulled out while you are away. Put the destination chair back after leaving it. Move as you normally would; you may ask for help or stop at any time.”
Start with the mover seated at A and both chairs on their rest marks. Say “Go” and start the timer. Once the mover is settled at B, hold for ten seconds, then say “Return”. Stop timing when the mover is seated back at A and both chairs are restored, or when the mover declares the attempt finished. An unfinished chair reset is recorded separately. Measure final offsets before the crew resets anything. If the run stops early, record elapsed time and stage, not a completed-cycle time.
Observer reference: the following is the digital chair sequence, not a posture prescription. Observe the participant's actual sequence. A different side, grip or chair movement is a finding to record, not automatically a failed trial.
- A out while seated. Digital reference: A and the seated body move backwards by 300 mm. Record the actual distance and whether the person instead stands first.
- Stand and leave A. Record exit side and twisting. A remains pulled out and reserved until the final return.
- Approach and pull B. Digital reference: a standing hand on the backrest pulls B out by 300 mm. Record approach side, hand and grip actually used.
- Enter, sit and move B in. Digital reference: the person sits, then moves B to its rest position while seated. Record alternatives. Give the ten-second hold only after the person settles.
- Move B out again, then rise and leave. Digital reference: slide B backwards by 300 mm while seated before rising. Record this second pull separately from step 3; do not omit it.
- Restore B while standing. Digital reference: a backrest grip returns B to its rest position. A must still remain pulled out. Record assistance or failure to restore.
- Return to A and sit. A remains in its pulled-out position until the person is seated. Record entry side and any change to A while the person was away.
- Move A in while seated. Digital reference: return A to its rest mark. Check the final seated position and both chair offsets; end the timer.
The tested digital route leaves A on the mover's left and enters B on the mover's right, relative to facing each table, with a right-hand destination grip. Keep this information for the observer. Do not force a 300 mm pull, a 550 mm side-step or a 75° turn. The latter belongs to a superseded, different case. An optional coached demonstration belongs in a separately labelled follow-up, after all natural trials, and is excluded from this comparison.
04 / Stop, reset, record and decide
Stop immediately on request, discomfort, loss of balance, a shifting support, or unexpected body contact with furniture, boundary or another person. Ordinary seat contact and an intentional chair grip are expected; record unexpected contact as body part ↔ object and stage. The facilitator may assist to end a run. Assistance is always recorded.
- Complete the two-page record for every run. Include participant, layout, revision, occupancy, order, practice flag, rest duration, actual seated hold and total/elapsed time. Record exit/entry sides and hand, all chair pulls, whether A stayed out, contact, participant-described twisting/discomfort, assistance and final chair offsets. Leave unknown values blank and mark “not measured”; never copy digital results into observation fields.
- Assign one overall outcome. Complete / unaided: returned seated, both chairs restored, no help. Complete / assisted: same finish with help. Stopped: did not finish. Movement finished / reset incomplete: returned but a chair is not restored. For each chair, record the largest displacement of any marked foot/rail reference point from its rest position, so rotation is included. Use ±5 mm as the operational reset target only. Do not call any category a comfort certification.
- Reset after measuring. Crew restores A and B to their rest marks, confirms the other ten chair positions, empty/reserved seats, peer positions and boundary stability. Recheck the datum at the start of each layout block and whenever anything shifts. Do not push A in during a run to clear space.
- Keep stopped and assisted records. Record the reason, stage, body location and chair states. One optional retry is allowed after resolving the cause and a full reset, only if the participant wants it. Append
-R1to the run ID and retain the original. A physical change starts a new revision; never silently replace a stopped result. - Compare within each condition. Compare E1/E2 against E1/E2 for the same mover in the other layout; compare O1 only against its matched O1. Keep practice, retries, assisted runs, incomplete resets and coached trials visibly separate. Review contact locations and participant wording before timings. Timing includes handling and the seated hold; it is not walking speed.
- Decide the next revision. If furniture needs changing, apply the same change to B′72 and B72, retain 72 seats, recheck geometry and issue new setting-out/record revision IDs before retesting both. Do not alter only the unsuccessful layout and call it the same comparison.
Interpretation: the current digital checks establish a nominal declared cycle only. This local mockup cannot establish whole-room access, continued conversation, comfort across body sizes, scent reduction or duct performance. The 100 mm local buffer from the separate lower-exposure case does not apply here.
Source: C1 setting-out kit and declared cycle; P1 physical-observation procedure. This document records instructions, not test results.
Later / W1 full-journey field kit. Review C1 observations before moving to the full-room pilot.